FAQ & Troubleshooting
FAQ & Troubleshooting
Get Our Support Videos Sorted by Product
Cordless
WYBOT C1
WYBOT C2
Vision
WYBOT C2 Vision
Solar
WYBOT S2 Solar Vision
WYBOT S2 Solar
Skimmer
WYBOT F1
Support Video
How to turn on, set up, and turn off
How to take the product out of water
How to take out the filter basket
How to rinse the filter basket
How to put the product into water
How to maintain the product
How to load the filter basket
How to install the floating blocks
How to connect to APP
How to charge the product
How to calibrate the sensor via app
View All
FAQ
How do I install the robot's floating block attachment?
+
Please follow the installation steps shown in the video:WYBOT C1 (Click here) For tiled surfaces, we recommend using float blocks.
Why does water appear inside the product packaging?
+
Each unit undergoes meticulous underwater testing before packaging to ensure optimal performance upon delivery. Minor dampness or water stains on the machine are considered normal.
Why won’t the machine charge?
+
Before charging, ensure the device is turned off to prevent charging issues, and check for any water in the charging port, as dampness may lead to charging failure or port corrosion.
Why can't the machine climb smooth walls?
+
1.Please charge the battery immediately upon receiving the robotic pool cleaner.Please note that the machine needs to be fully charged before initial use.The indicator light is red when charging, and green when charging is complete. 2.Before charging, dry the charging pins with a dry towel, and then proceed with the charging. 3.When this cleaner is not in use, please charge it every three months for battery maintenance.
Support Video
How to turn on, set up, and turn off
How to turn on, set up, and turn off
How to take the product out of water
How to take out the filter basket
How to rinse the filter basket
How to put the product into water
How to maintain the product
How to load the filter basket
How to install the floating blocks
How to connect to APP
How to charge the product
How to calibrate the sensor via app
View All
FAQ
How do l use the WYBOT C2?
+
For detailed instructions, please watch our operation guide videos: WYBOT C2 Operation Guide
Why is the machine l received wet? ls this a used product?
+
Rest assured that we test every unit underwater before packaging to ensure it works properly before delivery. Therefore, it is normal for the machine to be slightly damp or have water stains.
Support Video
How to turn on, set up, and turn off
Precautions for ultra fine filters
How to take the product out of water
How to take out the filter basket
How to rinse the filter basket
How to put the product into water
How to maintain the product
How to load the filter basket
How to install the floating blocks
How to connect to APP
How to charge the product
How to calibrate the sensor via app
View All
FAQ
How do I use the C2 Vision?
+
For detailed instructions, please watch our operation guide videos: WYBOT C2 Vision Operation Guide
Why is the machine l received wet? ls this a used product?
+
Rest assured that we test every unit underwater before packaging to ensure it works properly before delivery. Therefore, it is normal for the machine to be slightly damp or have water stains.
Support Video
How to take the robot out of the docking station
How to Remove Solar Panel
How to recall the robot with the button on the docking station
How to recall the robot via the app
How to place the robot on the station and check the charging station
How to maintain the solar panel
How to install solar panels
How to correctly position
How to activate the robot with the button on the docking station
How to activate the robot via app
View All
FAQ
How do I use the S2 Solar Vision?
+
For detailed instructions, please watch our operation guide videos: WYBOT S2 Solar Vision Operation Guide
Why is the machine l received wet? ls this a used product?
+
Rest assured that we test every unit underwater before packaging to ensure it works properly before delivery. Therefore, it is normal for the machine to be slightly damp or have water stains.
What should I do if the product is not performing as expected?
+
We strongly recommend updating both the robot and dock to the latest firmware. We continuously optimize the user experience, and updating to the latest version will ensure optimal performance.
Best solution:
1. Check the current version in "About Device" in the APP
2. Enable automatic updates in the APP
3.Remove the robot from water and charge it using the AC adapter. Ensure the charging location has WiFi coverage (must match the WiFi information configured on the dock). During charging, the robot will automatically check and update firmware, taking approximately 30 minutes for the entire process.
Latest version numbers:
DS20 (Dock): 2.2.17
S2S (Robot): 1.7.6
How should I use the robot in different cleaning scenarios?
+
For heavily soiled pools (such as the first cleaning in spring), relying on the solar-powered dock to charge the robot may not provide enough energy for frequent cleaning. In these cases, use the AC adapter to charge the robot.
For routine maintenance, adjust the scheduled cleaning intervals based on how much sunlight reaches your dock. If your dock's location receives limited sunlight, schedule cleanings every 2 days or less frequently.
What is the best installation location for the charging dock?
+
Please refer to the page below. Dock Installation
Support Video
How to take the robot out of the docking station
How to Remove Solar Panel
How to recall the robot with the button on the dock
How to recall the robot via the app
How to place the robot on the stake and check the charging status
How to maintain the solar panel
How to install solar panels
How to correctly position
How to activate the robot with the button on the docking station
View All
FAQ
How do I use the S2 Solar?
+
For detailed instructions, please watch our operation guide videos: WYBOT S2 Solar Operation Guide
Why is the machine l received wet? ls this a used product?
+
Rest assured that we test every unit underwater before packaging to ensure it works properly before delivery. Therefore, it is normal for the machine to be slightly damp or have water stains.
What should I do if the product is not performing as expected?
+
We strongly recommend updating both the robot and dock to the latest firmware. We continuously optimize the user experience, and updating to the latest version will ensure optimal performance.
Best solution:
1. Check the current version in "About Device" in the APP
2. Enable automatic updates in the APP
3. Remove the robot from water and charge it using the AC adapter. Ensure the charging location has WiFi coverage (must match the WiFi information configured on the dock). During charging, the robot will automatically check and update firmware, taking approximately 30 minutes for the entire process.
Latest version numbers:
DS20 (Dock): 2.2.17
S2S (Robot): 1.7.6
How should I use the robot in different cleaning scenarios?
+
For heavily soiled pools (such as the first cleaning in spring), relying on the solar-powered dock to charge the robot may not provide enough energy for frequent cleaning. In these cases, use the AC adapter to charge the robot.
For routine maintenance, adjust the scheduled cleaning intervals based on how much sunlight reaches your dock. If your dock's location receives limited sunlight, schedule cleanings every 2 days or less frequently.
What is the best installation location for the charging dock?
+
Please refer to the page below. Dock Installation
Support Video
How to turn on, set up, and turn off
How to realize one button docking via APP
How to put the product into water
How to maintain the product
How to load the filter basket
How to connect to APP
How to charge with solar panel
How to charge the product
How to calibrate the sensor via app
WYBOT F1's Auto Escape
When to use anti stranding bars
Precautions for solar panels
How to use remote control
How to use anti stranding rod
How to take the product out of water
How to take out the filter basket
How to rinse the filter basket
View All
FAQ
How do I use the WYBOT F1?
+
For detailed instructions, please watch our operation guide videos: WYBOT F1 Operation Guide
How is it solar powered?
+
The unit needs to be placed in the pool/water for it to be solar-powered whether it powered off or powered on.
Does it include a DC charger?
+
No, it is sold separately and can be purchased as an option if needed.
Can it be used indoors?
+
It is recommended that a charger for indoor swimming pools be purchased and a DC adapter used to charge.